TRAINING CONVEYOR DESIGN

Deskripsi

The Conveyor Design course covers the fundamentals of belt conveyor engineering including: belt width and velocity selection, conveyor power demand, belt sag, drive traction, drive types, brakes and holdbacks, information on conveyor arrangements, vertical curves and transitions, material trajectory calculations etc. plus belt, idler and pulley selection. In many of these topics, outdated conventional design methods are challenged and alternative solutions provided.

While some people may feel that they already have an adequate understanding of these topics, the real value of this course comes from the fact that it is packed with practical information that is not available in other texts. This Conveyor Design course is suitable for engineers employed in the design, operation and maintenance of belt conveyor systems, from graduates with a few years experience, through to engineering and maintenance managers.

Menimbang cukup kompleknya materi pelatihan Conveyor Design ini bagi peserta, dibutuhkan training provider yang berpengalaman di bidangnya agar tidak membuat peserta tidak menjadi cepat bosan dan jenuh dalam mendalami bidang teknik ini.

. Tersedia kelas publik & in-house | Available Offline & Online

Tujuan

Dengan mengikuti pelatihan Conveyor Design Peserta dapat berbagi pengetahuan / sharing knowledge mengenai Conveyor Design dengan peserta dari perusahaan lain yang bergerak di bidang Mechanical

The objective of the conveyor design course is to give engineers a full understanding of the conveyor design and equipment selection process, together with features of belt conveyors that should be avoided. This knowledge can then be used, not only in the design of new conveyor systems, but also by project engineers involved with new conveyors or existing conveyor upgrades and by those involved with the operation or maintenance of conveyor systems.

Materi

1. Introduction, including brief history of belt conveying
2. Material properties
3.  Conveyor surcharge angle and burden edge distance selection, including the influence of loading area design and belt velocity on surcharge angles
4. Idler geometry, including troughing angle and centre roll length considerations
5. Belt width and velocity selection
6. Flooded belt considerations including determining the length of flooded belt resulting from overlapping stopping times and the approximate force required to extract material from a blocked chute
7. Conveyor power demand calculation
8. How conveyor design packages work, including basic information on rigid body acceleration and deceleration calculations
9. Differences between rigid body and flexible body dynamic analysis
10. Belt sag requirements
11. Drive traction calculations, including what actually happens at a drive pulley
12. Rubber v ceramic lagging
13. Outline of drive types
14. Brakes
15. Determination of holdback requirements
16. Transitions
17. Vertical curves
18. Conveyor layouts including features to avoid
19. Uneven wear problems on pulleys
20. Shuttle conveyors
21. Travelling trippers, including the design of tripper belt profiles
22. Take-up systems
23. Trajectory calculations
24. Conveyor belting
25. Skirt systems
26. Belt safety factor selection, a new method of assessing safety factors
27. Minimum pulley diameter determination
28. Pulleys
29. Conveyor alignment and belt tracking
30. Idlers
31. Some general info on the design and construction of the Channar 20 km conveying system
32. Studi Kasus / Praktek pemecahan masalah Conveyor Design

Metode Pelatihan

Pelatihan ini menggunakan metode yang interaktif dan aplikatif, sehingga peserta dapat lebih mudah memahami materi. Instruktur berpengalaman akan menyampaikan materi secara sistematis, sementara peserta akan mengikuti diskusi kelompok untuk mendalami konsep. Selain itu, pelatihan ini juga mencakup simulasi serta studi kasus yang membantu peserta memahami penerapan konsep secara langsung dalam dunia kerja. Dengan pendekatan ini, mereka tidak hanya memperoleh wawasan teoretis, tetapi juga mengembangkan keterampilan praktis yang dapat mereka terapkan sesuai dengan kebutuhan industri.

Peserta

Peserta yang dapat mengikuti training Conveyor Design ini adalah yang ingin mendalami bidang Mechanical Para karyawan di semua lini bagian Conveyor Design

Instruktur

Instruktur yang berkompeten di bidang Mechanical

Jadwal Berdiklat Training 2025

• Batch 1 : 6 – 7 Januari 2025 || 15 – 16 Januari 2025 || 22 – 23 Januari 2025
• Batch 2 : 3 – 4 Februari 2025 || 12 – 13 Februari 2025 || 27 – 28 Februari 2025
• Batch 3 : 5 – 6 Maret 2025 || 10 – 11 Maret 2025 || 19 – 20 Maret 2025
• Batch 4 : 14 – 15 April 2025 || 23 – 24 April 2025
• Batch 5 : 5 – 6 Mei 2025 || 14 – 15 Mei 2025 || 26 – 27 Mei 2025
• Batch 6 : 2 – 3 Juni 2025 || 11 – 12 Juni 2025 || 18 – 19 Juni 2025 || 23 – 24 Juni 2025
• Batch 7 : 2 – 3 Juli 2025 || 16 – 17 Juli 2025 || 30 – 31 Juli 2025
• Batch 8 : 4 – 5 Agustus 2025 || 13 – 14 Agustus 2025 || 20 – 21 Agustus 2025 || 29 – 30 Agustus 2025
• Batch 9 : 3 – 4 September 2025 || 10 – 11 September 2025 || 15 – 16 September 2025 || 24 – 25 September 2025
• Batch 10 : 8 – 9 Oktober 2025 || 13 – 14 Oktober 2025 || 22 – 23 Oktober 2025
• Batch 11 : 3 – 4 November 2025 || 12 – 13 November 2025 || 19 – 20 November 2025 || 26 – 27 November 2025
• Batch 12 : 1 – 2 Desember 2025 || 10 – 11 Desember 2025 || 17 – 18 Desember 2025 || 26 – 27 Desember 2025

. Ingin disesuaikan dengan waktu dan kebutuhan tim Anda?

Kami siap menyelenggarakan pelatihan in-house sesuai permintaan.

Investasi dan Lokasi